What Size Pvc For Shop Vac Dust Collection
-
Store Vac Dust Collection Pipe Size
I am installing shop vac collection for the panel saw and Ridgid aquiver sander. I ran a 6' slice of 1 one/2" pvc pipe betwixt the tools and the shop vac. I am wondering if I should have used ii" pvc; would there exist that much difference in airflow that it would be worth redoing it?
- Mike
-
-
Store-Vacs are non the blazon of suction devices that benefit from a larger hose/pipe. They rely on high static pressure which they get from their smaller diameter medium. Im no skillful, just Id approximate your best bet if attempting to stretch the distance of suction from a shop-vac would exist to leave the run at whatever bore the hose was that came with it.
If at get-go you don't succeed, redefine success!
-
exist careful when running a shop Vac as a dust collector. I killed iii of them doing that. One of them was a new Ridged. Shop vacs are not made to run very long at all.
No PHD, but I take a DD 214
- Yeah, nor are they meant to be over worked past increased resistance from things similar longer runs or multiple ports open at the same time. They really shouldnt be used for dust collection. Only we use that we got sometimes.
Originally Posted past Jim Finn 
exist careful when running a shop Vac every bit a grit collector. I killed three of them doing that. One of them was a new Ridged. Shop vacs are not made to run very long at all.
If at outset yous don't succeed, redefine success!
-
I don't get to use my store as much as I would similar but my shop vacuum is holding up fine and it is my merely grit collection. Universal motors are non going to terminal as long every bit an induction motor but we use hand held tools with universal motors all the time. My table saw has ane (Ryobi BT3100). So while I concord that a shop vac with a universal motor volition not run as many hours equally a DC with an induction motor, I am not sure it is an important point for a domicile store. Mine is at least six or 7 years old at this point. If it quit today I could replace it for possibly $100. I doubt information technology volition. I await to get at least ten years out of it. It sucks through a grit deputy and so it sees lilliputian dust which probably helps. Just information technology has been used to collect physical droppings and drywall dust and anything else I need sucked up. Forest grit is relatively easy on it.
What information technology doesn't do well is motion the volume of air necessary to get all the chips from my jointer or planner. So I sweep upward after them. But for tools within information technology'due south capability, it works fine. If I did this for a living, I'd need both a bigger shop and probably a DC.
I similar 2 inch PVC and used it to connect my shop vac to the cyclone. I may run a length over to my drill printing then I can pick up the chips at it also. I don't know how much difference 1.5 inch will make. I'd use it and see how well information technology works at this point.
-
I just finished upwards a dust drove installation merely didn't want to connect the panel saw or sander to information technology. The panel saw port is only 1 1/two" and the port on the sander is 2 one/ii". I didn't feel that the dust collector would work properly on those small ports. Besides, I didn't want to plug up the dust collector filters with the really fine dust from the sander. I have it hooked up with one 1/2" PVC considering that's what I had on manus. Initial tests went well but I'll monitor over fourth dimension with actual employ.
The shop vac would be used simply intermittently simply I wouldn't hesitate to run it for long periods of time or use it as a grit collector based on my previous experience with them. I have had 7 full-size Ridgid vacuums in the past 12 years. The one that I kept on the truck for site use lasted almost viii years. It was used heavily, driveling regularly, and ran for long periods of time. It was covered in paint, thinset, mortar, drywall mud and dust, and we used it for everything from saw dust, dirty h2o, concrete slurry, metal shavings, and annihilation else you lot could call up of. It was nevertheless working when I tossed it only it had developed a actually loud, abrasive whine which was unbearable. The other 6 vacuums are still in use and piece of work like new, even the ones that I am crude on.
- Mike
What Size Pvc For Shop Vac Dust Collection,
Source: https://sawmillcreek.org/showthread.php?247999-Shop-Vac-Dust-Collection-Pipe-Size
Posted by: pittmanhavess82.blogspot.com
0 Response to "What Size Pvc For Shop Vac Dust Collection"
Post a Comment